Air Cleaner
-
Hi-Performance / Hi-Flow Thermostat - V8 (160-Deg)
mr. gasket high-performance thermostats are designed to resist large variations in coolant pressures that can occur at high rpms. under these conditions, coolant temperature and pressure fight for control of... Learn More -
High Temperature Ceramic High/Low H4 Wiring Loom
This high quality ceramic H4 plug is perfect for use with high wattage globes. Supplied with removable plastic sleeve. Learn More -
High Tensile Bolt : 5/8 UNF (4" Length) Black
-
High Tensile Bolt : 7/16 UNF (4" Length) Black
7/16 x 4 UNF High Tensile Bolt Only Black Learn More -
High Torque Starter Motor (2.5HP, 10 tooth) : suit Hemi 6 / Slant 6 / Small Block LA / Big Block B/RB (suit 122 & 130 tooth ring gear)
Our new high torque starter motors boast a huge 2.5 horsepower, and is around just half the size of a factory fitted unit. Learn More -
High Torque Starter Motor (2.5HP, 9 tooth) : suits Hemi 6, Slant 6, Small Block, Big Block (with 148 tooth ring gear)
Direct bolt in replacement, no wire adapters required ** These direct fit all new high torque starter motors boast a huge 2.5 horsepower, whist being nearly half the size of... Learn More -
High Voltage Warning Decal : CL/CM
This decal was located on the left-side upper inner guard in the engine compartment, next to the electronic control module. this is a reproduction of the factory-fitted decal found on... Learn More -
High Volume Water Pump (alloy) : suit Small Block 273 / 318 / 340 / 360 /408
The 8 impeller design on this water pump is a highly efficient replacement for your Small Block pumping more water than the standard 6 impeller design. Learn More -
High-Low Dipper Switch: suit RV1/SV1/AP5/AP6/VC/VE/VF/VG/VH/VJ
Factory-correct hi-beam dipper switch for use in RV1-VJ vehicles. No modifications required to your factory wiring. Learn More -
Holley 1BBL AP5/AP6 Carburetor (remanufactured, suit cable)
As found on AP5 and early AP6 vehicles fitted with a 225 Slant 6 engine running accelerator cable (not linkage.) Supplied with brand new vac pot - not reconditioned. High... Learn More -
Holley 1BBL Carburetor (remanufactured, suit cable) fits assorted 1975 Dodge Plymouth
As found on many 1975 Dodge Plymouth with 225 Slant 6 engines (see full list below) Supplied with brand new vac pot - not reconditioned. High quality re-manufacture from the... Learn More -
Holley Adjustable Fuel Pressure Injection Regulator (suit EFI 15-60psi)
Holley adjustable fuel injection regulators are able to provide all of the fuel pressure that your high performance, fuel injected vehicle will require. They utilize a special wave spring to... Learn More -
Holley Classic Holley Carburetor : 750 CFM : 4 Barrel : Vacuum Secondaries (Shiny finish)
One of the most widely used Holley carbs of all times -the 0-80508S. Its dual feed fuel inlets assure you get all the fuel you need, and its 750 CFM... Learn More -
Holley Inline Fuel Pressure Regulator : 4.5-8 PSI
The needle and seat assemblies that are installed in most carburetors can sufficiently control fuel pressure up to about 8 psi. If the fuel pump is putting out more than... Learn More -
Holley Sniper Carter style EFI Self-Tuning Fuel Injection System : MASTER KIT: 350HP : Silver : BBD Flange : NA only
The Holley Sniper EFI Self-Tuning Fuel Injection System is the perfect upgrade for any classic running a Carter BBD carburettors. With its easy-to-install design, you won't need any computer... Learn More